Mixed crushing and competitive leaching of all electrode material components and metal collector fluid in the spent lithium battery.

Hydrometallurgy is a primary method for recovering cathode electrode materials from spent lithium-ion batteries (LIBs). Most of the current research materials are pure cathode electrode materials obtained through manual disassembly. However, the spent LIBs are typically broken as a whole during the actual industrial recycling which makes the electrode materials combined with the collector fluid. Therefore, the competitive leaching between metal collector fluid and electrode material was examined. The pyrolysis characteristics of the electrode materials were analyzed to determine the pyrolysis temperature. The electrode sheet was pyrolyzed and then crushed for competitive leaching. The effect of pyrolysis was analyzed by XPS. The competitive leaching behavior was studied based on leaching agent concentration, leaching time and leaching temperature. The composition and morphology of the residue were determined to prove the competitive leaching results by XRD-SEM. TG results showed that 500 °C was the suitable pyrolysis temperature. XPS analysis demonstrated that pyrolysis can completely remove PVDF. Li and Co were preferentially leached during the competitive leaching while the leaching rates were 90.10% and 93.40% with 50 min leaching at 70 °C. The Al and Cu had weak competitive leachability and the leaching rate was 29.10% and 0.00%. XRD-SEM analysis showed that Li and Co can be fully leached with residual Al and Cu remaining. The results showed that the mixed leaching of electrode materials is feasible based on its excellent selective leaching properties.

Review on the gentle hydrometallurgical treatment of WPCBs: Sustainable and selective gradient process for multiple valuable metals recovery.

The metal resource crisis and the inherent need for a low-carbon circular economy have driven the rapid development of e-waste recycling technology. High-value waste printed circuit boards (WPCBs) are an essential component of e-waste. However, WPCBs are considered hazardous to the ecosystem due to the presence of heavy metals and brominated organic polymers. Therefore, achieving the recycling of metals in WPCBs is not only a strategic requirement for building a green ecological civilization but also an essential guarantee for achieving a safe supply of mineral resources. This review systematically analyzes the hydrometallurgical technology of metals in WPCBs in recent years. Firstly, the different unit operations of pretreatment in the hydrometallurgical process, which contain disassembly, crushing, and pre-enrichment, were analyzed. Secondly, environmentally friendly hydrometallurgical leaching systems and high-value product regeneration technologies used in recent years to recover metals from WPCBs were evaluated. The leaching techniques, including cyanidation, halide, thiourea, and thiosulfate for precious metals, and inorganic acid, organic acid, and other leaching methods for base metals such as copper and nickel in WPCBs, were outlined, and the leaching performance and greenness of each leaching system were summarized and analyzed. Eventually, based on the advantages of each leaching system and the differences in chemical properties of metals in WPCBs, an integrated and multi-gradient green process for the recovery of WPCBs was proposed, which provides a sustainable pathway for the recovery of metals in WPCBs. This paper provides a reference for realizing the gradient hydrometallurgical recovery of metals from WPCBs to promote the recycling metal resources.

Eco-friendly approach for enhancing the floatability of non-metallic components in waste printed circuit boards: Adding gutter oil during dry grinding.

Waste printed circuit boards (WPCBs) are an attractive secondary resource that is challenging to dispose of due to its complexity. Reverse flotation is an effective method to remove non-metallic particles (NMPs) to obtain metals from WPCBs. Nevertheless, the removal of NMPs is usually inadequate in the present flotation practice. Thus, to provide a clean approach to improve the removal efficiency of NMPs, the method of adding gutter oil during dry grinding process was adopted to enhance the hydrophobic sites on the surface of NMPs to improve the floatability. The surface morphology of NMPs was analyzed by SEM, the results show that the rough morphology inhibited the adhesion of bubbles, while water occupied the cracks and pores, making it challenging for collector adsorption, which result in unstable particle-bubble adhesion. The results of FTIR indicate that both NMPs and gutter oil have -CH3, -CH2, -C = O, -C-O functional groups, which promotes the adsorption of gutter oil on the surface of NMPs. The contact angle (CA) results show that the adsorption of gutter oil on the particle surface is conducive to the formation of enhanced CA. Furthermore, the flotation enhancement effect was verified by flotation kinetic experiments. The accumulated floats yield of NMPs conditioned by gutter oil during grinding is increased from 67.05% (NMPs without conditioning) to 95.02%, and the resin recovery is increased by 31.10%. It is demonstrated that dry grinding with gutter oil can strengthen the floatability of NMPs, which provides a potential approach to increase the flotation efficiency of WPCBs.

Enhanced cleaner flotation behavior of non-metallic particles in waste printed circuit boards: From the perspective of particle size.

Flotation is an attractive method for separating the different components of waste printed circuit boards (WPCBs) due to its cleanliness and efficiency. Non-metallic particles (NMPs) with good floatability usually need to be floated, however, it is difficult to achieve complete removal. The effect of particle size on the flotation behavior of NMPs, which is usually ignored in previous studies, is concerned in this paper. Flotation tests and kinetic analysis were carried out to reveal the effect of reagent dosage on flotation characteristics of particles in narrow size fractions. As the fineness decreases, the particles are more likely to be floated. Equally, the finer the particle size, the lower the reagent dosage required to achieve the maximum recovery. For 1-0.5 mm and -0.045 mm, the maximum recovery increased from 42.16% (1500 g/t MIBC) to 97.31% (100 g/t MIBC). Therefore, the feasibility of reducing particle size by grinding to improve floatability was verified. The results show that the reduction of particle size can significantly promote its efficiency of being floated. After grinding treatment, -0.045 mm yields in each size fraction (1-0.5, 0.5-0.25, 0.25-0.125, 0.125-0.074, 0.074-0.045 mm) increased by 22.10%, 28.42%, 30.90%, 64.56%, 89.32%, resulting in an increase of 37.71%, 13.12%, 2.82%, 7.82% and 2.00% in maximum recovery, respectively. It is also proved that the particle size, rather than the resin content, has a more significant effect on the floatability of NMPs.

Advanced utilization of copper in waste printed circuit boards: Synthesis of nano-copper assisted by physical enrichment.

The copper in the waste printed circuit boards (WPCBs) is cleanly recycled by physical methods and presented in the form of nano copper particles by hydrometallurgical, which provides environmental approach to the advanced utilization of metal copper. Copper in WPCBs was first pre-concentrated by gradient enrichment process including gravity separation, mechanical grinding and flotation. The leaching method was then used to dissolve copper from the flotation concentrate in ammoniacal/ammonium salt solutions. Subsequently, reduction treatment was conducted to synthesize nano-copper from leaching solution. The enrichment results of the clean physical separation process show that the grade of copper increased from 16.22% to -38.05% by gravity separation, and the grade of copper further increased to 72.62 % by flotation after dissociation, which avoids overgrinding of low value components. Copper nanoparticles can be prepared effectively, and the recovery of copper in the leaching process reaches 99 %. The particle size of copper nanoparticles obtained by ascorbic acid reduction is tens of nanometers, and the surface of copper nanoparticles is smooth and nearly spherical. The present study proposes an environmentally friendly process of preparing nano-copper from the copper in WPCBs.

Mechanical activation to enhance the natural floatability of waste printed circuit boards.

The metal in the waste printed circuit boards (WPCBs) is an excellent secondary metal resource. WPCBs were ground to dissociate, and impurities in the dissociated product were removed by gradient flotation to recover valuable metals in this study. The effects of crushing methods on size composition and dissociation state of the crushed products were studied. Then the gradient flotation experiment was designed to verify the natural floatability of ground materials. Grinding test shows that impact crushing has greater grinding fineness (-0.074 mm) than shear crushing, which is 42.14% and 26.18% respectively with 5 min grinding. The flotation test results illustrate that the natural floatability of impurities increases with the grinding fineness, that is, the yield of floats increases without flotation reagents. For impact crushing and shear crushing, the floats yields are 38.48% and 31.75% respectively, accompanied by 70.53% and 65.46% impurity removal for ground materials with 5 min grinding. Subsequently, 21.61% and 26.35% of impurities can be further removed with the aid of collector. Finally, the recovery of Cu in concentrate reaches 67.84% and 65.75%, respectively. FT-IR proves that the excellent floatability of particles is caused by the significant hydrophobic group. Mechanical grinding has been proved to have double effects of improving dissociation and natural floatability.

Flotation dynamics of metal and non-metal components in waste printed circuit boards.

Flotation is an effective and clean separation technology to realize the recovery of metal in waste printed circuit boards (WPCBs). The flotation kinetic of metal and non-metal components was concerned in this study. In addition, the loading of bubbles, the collision and shedding of particles and bubbles were used to assist in proving the particle dynamics results. By analyzing the force on the particles, the load of bubbles on particles was analyzed, and the appropriate volume ratio of bubbles to particles was 1.5-8.0, depending on the particle density. Moreover, Clift model and Schiller-Naumann model has high fitting accuracy for the final bubble velocity. In addition, metal particles have greater settling velocity, which results in shorter collision time with bubbles. In the process of bubble-particle rising, the shedding probability gradually decreases, and the shedding probability of metal particles is much higher than that of non-metal particles. The results of flotation kinetics show that the removal of impurity particles represented by silicon mainly occurs in the initial stage of flotation process. The loss of copper increases with flotation time and collector dosage. This study reveals the flotation kinetics of particles from the perspectives of bubble loading, bubble-particle collision and shedding.

Recovery of metals in waste printed circuit boards by flotation technology with soap collector prepared by waste oil through saponification.

Recycling metal from waste printed circuit boards (WPCBs) through green flotation technology has been concerned in this paper. For the sake of environmentally friendly of flotation process, a renewable collector was prepared from waste oil by saponification reaction. The collector composition was analyzed by GC-MS, and results show that the main compositions are n-Hexadecanoic acid, oleic acid and octadecanoic acid. XRD and XRF results show that copper is the main valuable element for recovery. Effects of collector dosage and pH on flotation behavior were analyzed. In addition, the feasibility of improving copper recovery by multiple sorting test processes was also verified. Flotation results show that the concentrate yield and metal recovery decreases with the increase of collector dosage, accompanied by the increase of copper grade. When the dosage of collector is 3 kg/t, concentrate with 22% yield, 66% copper grade, and 47% copper recovery is obtained. Furthermore, concentrate yield and metal recovery rate first decrease and then increase with the increase of pH, while copper content first increase and then decrease. The suitable pH of the separation process is neutral environment (pH = 6-8). The study provides an alternative process for the recovery of metals in WPCBs.

Silver-containing dressing for surgical site infection in clean and clean-contaminated operations: a systematic review and meta-analysis of randomized controlled trials.

BACKGROUND: Silver-containing dressings for the prevention of surgical site infections (SSIs) remained controversial, and accumulating evidence was lacking, so a meta-analysis was conducted to systematically assess the effectiveness and safety of silver-containing dressings for clean and clean-contaminated surgical incisions. METHODS: Pubmed, Embase, and the Cochrane Library were searched from the inception to February 2016 for randomized controlled trials (RCTs), which explored silver-containing dressings for the prevention of SSIs in clean and clean-contaminated operations. Relative risk (RR) with 95% confidence interval (CI) was pooled using random effects model. Predefined subgroup analyses, sensitivity analyses, and influence analyses were further undertaken. RESULTS: Nine RCTs totaling 2196 patients (1141 in silver-containing group and 1055 in control group) were included. Silver-containing dressings did not effectively prevent the incidence of SSIs (9 RCTs; RR: 0.92; 95% CI: 0.66-1.29; I2 = 40%), superficial SSIs (5 RCTs; RR: 0.67; 95% CI: 0.36-1.24; I2 = 36%), and deep SSIs (5 RCTs; RR: 0.78; 95% CI: 0.41-1.49; I2 = 0). Subgroup analyses, sensitivity analyses, and influence analyses confirmed the robustness of the pooled estimate. CONCLUSIONS: The current available evidence indicated that silver-containing dressing as compared with silver-free dressing was not associated with lower incidence of SSIs. Considering the quality of evidence ranking very low, further studies with higher quality should be warranted.

Laparoscopic-assisted versus open radical gastrectomy for resectable gastric cancer: Systematic review, meta-analysis, and trial sequential analysis of randomized controlled trials.

BACKGROUND: Previous studies comparing laparoscopic-assisted to open gastrectomy (OG) for resectable gastric cancer were inexhaustive, so an updated meta-analysis was performed to clarify quality of life, patient satisfaction, safety and effectiveness associated with laparoscopic-assisted gastrectomy (LAG). METHODS: Pubmed, Embase, and The Cochrane Library were searched from inception to December 2015 for randomized controlled trials (RCTs) comparing LAG with OG for resectable gastric cancer. Relative risk (RR) and weighted mean difference (WMD) with 95% confidence intervals (CIs) were pooled with random-effects model. Furthermore, trial sequential analysis (TSA) was employed to indicate the credibility of pooled estimate. RESULTS: Fourteen RCTs totaling 2,307 gastric cancer patients (1,163 in laparoscopic and 1,144 in open) were included. Compared with OG, LAG showed higher patient satisfaction and quality of life, less blood loss, hospital stay and overall postoperative morbidity, and longer operating time, which were confirmed by TSA. LAG also accelerated time to first flatus, first walking and first intake and reduced frequency of analgesic administration and days of fever. There were no significant difference between the two groups in number of retrieved lymph nodes, mortality, recurrence, long-term overall survival and disease-free survival. CONCLUSION: For patients with resectable gastric cancer, LAG decreased blood loss, length of hospital stay and overall postoperative morbidity and improved postsurgical recovery. J. Surg. Oncol. 2016;113:756-767. © 2016 Wiley Periodicals, Inc.